990 lines
44 KiB
Plaintext
990 lines
44 KiB
Plaintext
# Config file for mosquitto
|
|
#
|
|
# See mosquitto.conf(5) for more information.
|
|
#
|
|
# Default values are shown, uncomment to change.
|
|
#
|
|
# Use the # character to indicate a comment, but only if it is the
|
|
# very first character on the line.
|
|
|
|
# =================================================================
|
|
# General configuration
|
|
# =================================================================
|
|
|
|
# Use per listener security settings.
|
|
#
|
|
# It is recommended this option be set before any other options.
|
|
#
|
|
# If this option is set to true, then all authentication and access control
|
|
# options are controlled on a per listener basis. The following options are
|
|
# affected:
|
|
#
|
|
# password_file acl_file psk_file auth_plugin auth_opt_* allow_anonymous
|
|
# auto_id_prefix allow_zero_length_clientid
|
|
#
|
|
# Note that if set to true, then a durable client (i.e. with clean session set
|
|
# to false) that has disconnected will use the ACL settings defined for the
|
|
# listener that it was most recently connected to.
|
|
#
|
|
# The default behaviour is for this to be set to false, which maintains the
|
|
# setting behaviour from previous versions of mosquitto.
|
|
per_listener_settings true
|
|
password_file /mosquitto/config/passwordfile
|
|
|
|
|
|
# If a client is subscribed to multiple subscriptions that overlap, e.g. foo/#
|
|
# and foo/+/baz , then MQTT expects that when the broker receives a message on
|
|
# a topic that matches both subscriptions, such as foo/bar/baz, then the client
|
|
# should only receive the message once.
|
|
# Mosquitto keeps track of which clients a message has been sent to in order to
|
|
# meet this requirement. The allow_duplicate_messages option allows this
|
|
# behaviour to be disabled, which may be useful if you have a large number of
|
|
# clients subscribed to the same set of topics and are very concerned about
|
|
# minimising memory usage.
|
|
# It can be safely set to true if you know in advance that your clients will
|
|
# never have overlapping subscriptions, otherwise your clients must be able to
|
|
# correctly deal with duplicate messages even when then have QoS=2.
|
|
#allow_duplicate_messages false
|
|
|
|
# This option controls whether a client is allowed to connect with a zero
|
|
# length client id or not. This option only affects clients using MQTT v3.1.1
|
|
# and later. If set to false, clients connecting with a zero length client id
|
|
# are disconnected. If set to true, clients will be allocated a client id by
|
|
# the broker. This means it is only useful for clients with clean session set
|
|
# to true.
|
|
#allow_zero_length_clientid true
|
|
|
|
# If allow_zero_length_clientid is true, this option allows you to set a prefix
|
|
# to automatically generated client ids to aid visibility in logs.
|
|
# Defaults to 'auto-'
|
|
#auto_id_prefix auto-
|
|
|
|
# This option affects the scenario when a client subscribes to a topic that has
|
|
# retained messages. It is possible that the client that published the retained
|
|
# message to the topic had access at the time they published, but that access
|
|
# has been subsequently removed. If check_retain_source is set to true, the
|
|
# default, the source of a retained message will be checked for access rights
|
|
# before it is republished. When set to false, no check will be made and the
|
|
# retained message will always be published. This affects all listeners.
|
|
#check_retain_source true
|
|
|
|
# QoS 1 and 2 messages will be allowed inflight per client until this limit
|
|
# is exceeded. Defaults to 0. (No maximum)
|
|
# See also max_inflight_messages
|
|
#max_inflight_bytes 0
|
|
|
|
# The maximum number of QoS 1 and 2 messages currently inflight per
|
|
# client.
|
|
# This includes messages that are partway through handshakes and
|
|
# those that are being retried. Defaults to 20. Set to 0 for no
|
|
# maximum. Setting to 1 will guarantee in-order delivery of QoS 1
|
|
# and 2 messages.
|
|
#max_inflight_messages 20
|
|
|
|
# For MQTT v5 clients, it is possible to have the server send a "server
|
|
# keepalive" value that will override the keepalive value set by the client.
|
|
# This is intended to be used as a mechanism to say that the server will
|
|
# disconnect the client earlier than it anticipated, and that the client should
|
|
# use the new keepalive value. The max_keepalive option allows you to specify
|
|
# that clients may only connect with keepalive less than or equal to this
|
|
# value, otherwise they will be sent a server keepalive telling them to use
|
|
# max_keepalive. This only applies to MQTT v5 clients. The maximum value
|
|
# allowable is 65535. Do not set below 10.
|
|
#max_keepalive 65535
|
|
|
|
# For MQTT v5 clients, it is possible to have the server send a "maximum packet
|
|
# size" value that will instruct the client it will not accept MQTT packets
|
|
# with size greater than max_packet_size bytes. This applies to the full MQTT
|
|
# packet, not just the payload. Setting this option to a positive value will
|
|
# set the maximum packet size to that number of bytes. If a client sends a
|
|
# packet which is larger than this value, it will be disconnected. This applies
|
|
# to all clients regardless of the protocol version they are using, but v3.1.1
|
|
# and earlier clients will of course not have received the maximum packet size
|
|
# information. Defaults to no limit. Setting below 20 bytes is forbidden
|
|
# because it is likely to interfere with ordinary client operation, even with
|
|
# very small payloads.
|
|
#max_packet_size 0
|
|
|
|
# QoS 1 and 2 messages above those currently in-flight will be queued per
|
|
# client until this limit is exceeded. Defaults to 0. (No maximum)
|
|
# See also max_queued_messages.
|
|
# If both max_queued_messages and max_queued_bytes are specified, packets will
|
|
# be queued until the first limit is reached.
|
|
#max_queued_bytes 0
|
|
|
|
# The maximum number of QoS 1 and 2 messages to hold in a queue per client
|
|
# above those that are currently in-flight. Defaults to 100. Set
|
|
# to 0 for no maximum (not recommended).
|
|
# See also queue_qos0_messages.
|
|
# See also max_queued_bytes.
|
|
#max_queued_messages 100
|
|
#
|
|
# This option sets the maximum number of heap memory bytes that the broker will
|
|
# allocate, and hence sets a hard limit on memory use by the broker. Memory
|
|
# requests that exceed this value will be denied. The effect will vary
|
|
# depending on what has been denied. If an incoming message is being processed,
|
|
# then the message will be dropped and the publishing client will be
|
|
# disconnected. If an outgoing message is being sent, then the individual
|
|
# message will be dropped and the receiving client will be disconnected.
|
|
# Defaults to no limit.
|
|
#memory_limit 0
|
|
|
|
# This option sets the maximum publish payload size that the broker will allow.
|
|
# Received messages that exceed this size will not be accepted by the broker.
|
|
# The default value is 0, which means that all valid MQTT messages are
|
|
# accepted. MQTT imposes a maximum payload size of 268435455 bytes.
|
|
#message_size_limit 0
|
|
|
|
# This option allows persistent clients (those with clean session set to false)
|
|
# to be removed if they do not reconnect within a certain time frame.
|
|
#
|
|
# This is a non-standard option in MQTT V3.1 but allowed in MQTT v3.1.1.
|
|
#
|
|
# Badly designed clients may set clean session to false whilst using a randomly
|
|
# generated client id. This leads to persistent clients that will never
|
|
# reconnect. This option allows these clients to be removed.
|
|
#
|
|
# The expiration period should be an integer followed by one of h d w m y for
|
|
# hour, day, week, month and year respectively. For example
|
|
#
|
|
# persistent_client_expiration 2m
|
|
# persistent_client_expiration 14d
|
|
# persistent_client_expiration 1y
|
|
#
|
|
# The default if not set is to never expire persistent clients.
|
|
#persistent_client_expiration
|
|
|
|
# Write process id to a file. Default is a blank string which means
|
|
# a pid file shouldn't be written.
|
|
# This should be set to /var/run/mosquitto.pid if mosquitto is
|
|
# being run automatically on boot with an init script and
|
|
# start-stop-daemon or similar.
|
|
#pid_file
|
|
|
|
# Set to true to queue messages with QoS 0 when a persistent client is
|
|
# disconnected. These messages are included in the limit imposed by
|
|
# max_queued_messages and max_queued_bytes
|
|
# Defaults to false.
|
|
# This is a non-standard option for the MQTT v3.1 spec but is allowed in
|
|
# v3.1.1.
|
|
#queue_qos0_messages false
|
|
|
|
# Set to false to disable retained message support. If a client publishes a
|
|
# message with the retain bit set, it will be disconnected if this is set to
|
|
# false.
|
|
#retain_available true
|
|
|
|
# Disable Nagle's algorithm on client sockets. This has the effect of reducing
|
|
# latency of individual messages at the potential cost of increasing the number
|
|
# of packets being sent.
|
|
#set_tcp_nodelay false
|
|
|
|
# Time in seconds between updates of the $SYS tree.
|
|
# Set to 0 to disable the publishing of the $SYS tree.
|
|
#sys_interval 10
|
|
|
|
# The MQTT specification requires that the QoS of a message delivered to a
|
|
# subscriber is never upgraded to match the QoS of the subscription. Enabling
|
|
# this option changes this behaviour. If upgrade_outgoing_qos is set true,
|
|
# messages sent to a subscriber will always match the QoS of its subscription.
|
|
# This is a non-standard option explicitly disallowed by the spec.
|
|
#upgrade_outgoing_qos false
|
|
|
|
# When run as root, drop privileges to this user and its primary
|
|
# group.
|
|
# Set to root to stay as root, but this is not recommended.
|
|
# If run as a non-root user, this setting has no effect.
|
|
# Note that on Windows this has no effect and so mosquitto should
|
|
# be started by the user you wish it to run as.
|
|
#user mosquitto
|
|
|
|
# =================================================================
|
|
# Default listener
|
|
# =================================================================
|
|
|
|
# IP address/hostname to bind the default listener to. If not
|
|
# given, the default listener will not be bound to a specific
|
|
# address and so will be accessible to all network interfaces.
|
|
# bind_address ip-address/host name
|
|
#bind_address
|
|
|
|
# Port to use for the default listener.
|
|
#port 1883
|
|
|
|
# Bind the listener to a specific interface. This is similar to
|
|
# bind_address above but is useful when an interface has multiple addresses or
|
|
# the address may change. It is valid to use this with the bind_address option,
|
|
# but take care that the interface you are binding to contains the address you
|
|
# are binding to, otherwise you will not be able to connect.
|
|
# Example: bind_interface eth0
|
|
#bind_interface
|
|
|
|
# When a listener is using the websockets protocol, it is possible to serve
|
|
# http data as well. Set http_dir to a directory which contains the files you
|
|
# wish to serve. If this option is not specified, then no normal http
|
|
# connections will be possible.
|
|
#http_dir
|
|
|
|
# The maximum number of client connections to allow. This is
|
|
# a per listener setting.
|
|
# Default is -1, which means unlimited connections.
|
|
# Note that other process limits mean that unlimited connections
|
|
# are not really possible. Typically the default maximum number of
|
|
# connections possible is around 1024.
|
|
#max_connections -1
|
|
|
|
# Choose the protocol to use when listening.
|
|
# This can be either mqtt or websockets.
|
|
# Websockets support is currently disabled by default at compile time.
|
|
# Certificate based TLS may be used with websockets, except that
|
|
# only the cafile, certfile, keyfile and ciphers options are supported.
|
|
#protocol mqtt
|
|
|
|
# Set use_username_as_clientid to true to replace the clientid that a client
|
|
# connected with with its username. This allows authentication to be tied to
|
|
# the clientid, which means that it is possible to prevent one client
|
|
# disconnecting another by using the same clientid.
|
|
# If a client connects with no username it will be disconnected as not
|
|
# authorised when this option is set to true.
|
|
# Do not use in conjunction with clientid_prefixes.
|
|
# See also use_identity_as_username.
|
|
#use_username_as_clientid
|
|
|
|
# -----------------------------------------------------------------
|
|
# Certificate based SSL/TLS support
|
|
# -----------------------------------------------------------------
|
|
# The following options can be used to enable SSL/TLS support for
|
|
# this listener. Note that the recommended port for MQTT over TLS
|
|
# is 8883, but this must be set manually.
|
|
#
|
|
# See also the mosquitto-tls man page.
|
|
|
|
# At least one of cafile or capath must be defined. They both
|
|
# define methods of accessing the PEM encoded Certificate
|
|
# Authority certificates that have signed your server certificate
|
|
# and that you wish to trust.
|
|
# cafile defines the path to a file containing the CA certificates.
|
|
# capath defines a directory that will be searched for files
|
|
# containing the CA certificates. For capath to work correctly, the
|
|
# certificate files must have ".crt" as the file ending and you must run
|
|
# "openssl rehash <path to capath>" each time you add/remove a certificate.
|
|
#cafile
|
|
#capath
|
|
|
|
# Path to the PEM encoded server certificate.
|
|
#certfile
|
|
|
|
# Path to the PEM encoded keyfile.
|
|
#keyfile
|
|
|
|
|
|
# If you have require_certificate set to true, you can create a certificate
|
|
# revocation list file to revoke access to particular client certificates. If
|
|
# you have done this, use crlfile to point to the PEM encoded revocation file.
|
|
#crlfile
|
|
|
|
# If you wish to control which encryption ciphers are used, use the ciphers
|
|
# option. The list of available ciphers can be obtained using the "openssl
|
|
# ciphers" command and should be provided in the same format as the output of
|
|
# that command.
|
|
# If unset defaults to DEFAULT:!aNULL:!eNULL:!LOW:!EXPORT:!SSLv2:@STRENGTH
|
|
#ciphers DEFAULT:!aNULL:!eNULL:!LOW:!EXPORT:!SSLv2:@STRENGTH
|
|
|
|
# To allow the use of ephemeral DH key exchange, which provides forward
|
|
# security, the listener must load DH parameters. This can be specified with
|
|
# the dhparamfile option. The dhparamfile can be generated with the command
|
|
# e.g. "openssl dhparam -out dhparam.pem 2048"
|
|
#dhparamfile
|
|
|
|
# By default a TLS enabled listener will operate in a similar fashion to a
|
|
# https enabled web server, in that the server has a certificate signed by a CA
|
|
# and the client will verify that it is a trusted certificate. The overall aim
|
|
# is encryption of the network traffic. By setting require_certificate to true,
|
|
# the client must provide a valid certificate in order for the network
|
|
# connection to proceed. This allows access to the broker to be controlled
|
|
# outside of the mechanisms provided by MQTT.
|
|
#require_certificate false
|
|
|
|
# This option defines the version of the TLS protocol to use for this listener.
|
|
# The default value allows all of v1.3, v1.2 and v1.1. The valid values are
|
|
# tlsv1.3 tlsv1.2 and tlsv1.1.
|
|
#tls_version
|
|
|
|
# If require_certificate is true, you may set use_identity_as_username to true
|
|
# to use the CN value from the client certificate as a username. If this is
|
|
# true, the password_file option will not be used for this listener.
|
|
# This takes priority over use_subject_as_username.
|
|
# See also use_subject_as_username.
|
|
#use_identity_as_username false
|
|
|
|
# If require_certificate is true, you may set use_subject_as_username to true
|
|
# to use the complete subject value from the client certificate as a username.
|
|
# If this is true, the password_file option will not be used for this listener.
|
|
# See also use_identity_as_username
|
|
#use_subject_as_username false
|
|
|
|
# -----------------------------------------------------------------
|
|
# Pre-shared-key based SSL/TLS support
|
|
# -----------------------------------------------------------------
|
|
# The following options can be used to enable PSK based SSL/TLS support for
|
|
# this listener. Note that the recommended port for MQTT over TLS is 8883, but
|
|
# this must be set manually.
|
|
#
|
|
# See also the mosquitto-tls man page and the "Certificate based SSL/TLS
|
|
# support" section. Only one of certificate or PSK encryption support can be
|
|
# enabled for any listener.
|
|
|
|
# The psk_hint option enables pre-shared-key support for this listener and also
|
|
# acts as an identifier for this listener. The hint is sent to clients and may
|
|
# be used locally to aid authentication. The hint is a free form string that
|
|
# doesn't have much meaning in itself, so feel free to be creative.
|
|
# If this option is provided, see psk_file to define the pre-shared keys to be
|
|
# used or create a security plugin to handle them.
|
|
#psk_hint
|
|
|
|
# When using PSK, the encryption ciphers used will be chosen from the list of
|
|
# available PSK ciphers. If you want to control which ciphers are available,
|
|
# use the "ciphers" option. The list of available ciphers can be obtained
|
|
# using the "openssl ciphers" command and should be provided in the same format
|
|
# as the output of that command.
|
|
#ciphers
|
|
|
|
# Set use_identity_as_username to have the psk identity sent by the client used
|
|
# as its username. Authentication will be carried out using the PSK rather than
|
|
# the MQTT username/password and so password_file will not be used for this
|
|
# listener.
|
|
#use_identity_as_username false
|
|
|
|
|
|
# =================================================================
|
|
# Extra listeners
|
|
# =================================================================
|
|
|
|
# Listen on a port/ip address combination. By using this variable
|
|
# multiple times, mosquitto can listen on more than one port. If
|
|
# this variable is used and neither bind_address nor port given,
|
|
# then the default listener will not be started.
|
|
# The port number to listen on must be given. Optionally, an ip
|
|
# address or host name may be supplied as a second argument. In
|
|
# this case, mosquitto will attempt to bind the listener to that
|
|
# address and so restrict access to the associated network and
|
|
# interface. By default, mosquitto will listen on all interfaces.
|
|
# Note that for a websockets listener it is not possible to bind to a host
|
|
# name.
|
|
# listener port-number [ip address/host name]
|
|
#listener
|
|
|
|
# Bind the listener to a specific interface. This is similar to
|
|
# the [ip address/host name] part of the listener definition, but is useful
|
|
# when an interface has multiple addresses or the address may change. It is
|
|
# valid to use this with the [ip address/host name] part of the listener
|
|
# definition, but take care that the interface you are binding to contains the
|
|
# address you are binding to, otherwise you will not be able to connect.
|
|
# Only available on Linux and requires elevated privileges.
|
|
#
|
|
# Example: bind_interface eth0
|
|
#bind_interface
|
|
|
|
# When a listener is using the websockets protocol, it is possible to serve
|
|
# http data as well. Set http_dir to a directory which contains the files you
|
|
# wish to serve. If this option is not specified, then no normal http
|
|
# connections will be possible.
|
|
#http_dir
|
|
|
|
# The maximum number of client connections to allow. This is
|
|
# a per listener setting.
|
|
# Default is -1, which means unlimited connections.
|
|
# Note that other process limits mean that unlimited connections
|
|
# are not really possible. Typically the default maximum number of
|
|
# connections possible is around 1024.
|
|
#max_connections -1
|
|
|
|
# The listener can be restricted to operating within a topic hierarchy using
|
|
# the mount_point option. This is achieved be prefixing the mount_point string
|
|
# to all topics for any clients connected to this listener. This prefixing only
|
|
# happens internally to the broker; the client will not see the prefix.
|
|
#mount_point
|
|
|
|
# Choose the protocol to use when listening.
|
|
# This can be either mqtt or websockets.
|
|
# Certificate based TLS may be used with websockets, except that only the
|
|
# cafile, certfile, keyfile and ciphers options are supported.
|
|
#protocol mqtt
|
|
|
|
# Set use_username_as_clientid to true to replace the clientid that a client
|
|
# connected with with its username. This allows authentication to be tied to
|
|
# the clientid, which means that it is possible to prevent one client
|
|
# disconnecting another by using the same clientid.
|
|
# If a client connects with no username it will be disconnected as not
|
|
# authorised when this option is set to true.
|
|
# Do not use in conjunction with clientid_prefixes.
|
|
# See also use_identity_as_username.
|
|
#use_username_as_clientid
|
|
|
|
# Change the websockets headers size. This is a global option, it is not
|
|
# possible to set per listener. This option sets the size of the buffer used in
|
|
# the libwebsockets library when reading HTTP headers. If you are passing large
|
|
# header data such as cookies then you may need to increase this value. If left
|
|
# unset, or set to 0, then the default of 1024 bytes will be used.
|
|
#websockets_headers_size
|
|
|
|
# -----------------------------------------------------------------
|
|
# Certificate based SSL/TLS support
|
|
# -----------------------------------------------------------------
|
|
# The following options can be used to enable certificate based SSL/TLS support
|
|
# for this listener. Note that the recommended port for MQTT over TLS is 8883,
|
|
# but this must be set manually.
|
|
#
|
|
# See also the mosquitto-tls man page and the "Pre-shared-key based SSL/TLS
|
|
# support" section. Only one of certificate or PSK encryption support can be
|
|
# enabled for any listener.
|
|
|
|
# At least one of cafile or capath must be defined to enable certificate based
|
|
# TLS encryption. They both define methods of accessing the PEM encoded
|
|
# Certificate Authority certificates that have signed your server certificate
|
|
# and that you wish to trust.
|
|
# cafile defines the path to a file containing the CA certificates.
|
|
# capath defines a directory that will be searched for files
|
|
# containing the CA certificates. For capath to work correctly, the
|
|
# certificate files must have ".crt" as the file ending and you must run
|
|
# "openssl rehash <path to capath>" each time you add/remove a certificate.
|
|
#cafile
|
|
#capath
|
|
|
|
# Path to the PEM encoded server certificate.
|
|
#certfile
|
|
|
|
# Path to the PEM encoded keyfile.
|
|
#keyfile
|
|
|
|
|
|
# If you wish to control which encryption ciphers are used, use the ciphers
|
|
# option. The list of available ciphers can be optained using the "openssl
|
|
# ciphers" command and should be provided in the same format as the output of
|
|
# that command.
|
|
#ciphers
|
|
|
|
# If you have require_certificate set to true, you can create a certificate
|
|
# revocation list file to revoke access to particular client certificates. If
|
|
# you have done this, use crlfile to point to the PEM encoded revocation file.
|
|
#crlfile
|
|
|
|
# To allow the use of ephemeral DH key exchange, which provides forward
|
|
# security, the listener must load DH parameters. This can be specified with
|
|
# the dhparamfile option. The dhparamfile can be generated with the command
|
|
# e.g. "openssl dhparam -out dhparam.pem 2048"
|
|
#dhparamfile
|
|
|
|
# By default an TLS enabled listener will operate in a similar fashion to a
|
|
# https enabled web server, in that the server has a certificate signed by a CA
|
|
# and the client will verify that it is a trusted certificate. The overall aim
|
|
# is encryption of the network traffic. By setting require_certificate to true,
|
|
# the client must provide a valid certificate in order for the network
|
|
# connection to proceed. This allows access to the broker to be controlled
|
|
# outside of the mechanisms provided by MQTT.
|
|
#require_certificate false
|
|
|
|
# If require_certificate is true, you may set use_identity_as_username to true
|
|
# to use the CN value from the client certificate as a username. If this is
|
|
# true, the password_file option will not be used for this listener.
|
|
#use_identity_as_username false
|
|
|
|
# -----------------------------------------------------------------
|
|
# Pre-shared-key based SSL/TLS support
|
|
# -----------------------------------------------------------------
|
|
# The following options can be used to enable PSK based SSL/TLS support for
|
|
# this listener. Note that the recommended port for MQTT over TLS is 8883, but
|
|
# this must be set manually.
|
|
#
|
|
# See also the mosquitto-tls man page and the "Certificate based SSL/TLS
|
|
# support" section. Only one of certificate or PSK encryption support can be
|
|
# enabled for any listener.
|
|
|
|
# The psk_hint option enables pre-shared-key support for this listener and also
|
|
# acts as an identifier for this listener. The hint is sent to clients and may
|
|
# be used locally to aid authentication. The hint is a free form string that
|
|
# doesn't have much meaning in itself, so feel free to be creative.
|
|
# If this option is provided, see psk_file to define the pre-shared keys to be
|
|
# used or create a security plugin to handle them.
|
|
#psk_hint
|
|
|
|
# When using PSK, the encryption ciphers used will be chosen from the list of
|
|
# available PSK ciphers. If you want to control which ciphers are available,
|
|
# use the "ciphers" option. The list of available ciphers can be optained
|
|
# using the "openssl ciphers" command and should be provided in the same format
|
|
# as the output of that command.
|
|
#ciphers
|
|
|
|
# Set use_identity_as_username to have the psk identity sent by the client used
|
|
# as its username. Authentication will be carried out using the PSK rather than
|
|
# the MQTT username/password and so password_file will not be used for this
|
|
# listener.
|
|
#use_identity_as_username false
|
|
|
|
|
|
# =================================================================
|
|
# Persistence
|
|
# =================================================================
|
|
|
|
# If persistence is enabled, save the in-memory database to disk
|
|
# every autosave_interval seconds. If set to 0, the persistence
|
|
# database will only be written when mosquitto exits. See also
|
|
# autosave_on_changes.
|
|
# Note that writing of the persistence database can be forced by
|
|
# sending mosquitto a SIGUSR1 signal.
|
|
#autosave_interval 1800
|
|
|
|
# If true, mosquitto will count the number of subscription changes, retained
|
|
# messages received and queued messages and if the total exceeds
|
|
# autosave_interval then the in-memory database will be saved to disk.
|
|
# If false, mosquitto will save the in-memory database to disk by treating
|
|
# autosave_interval as a time in seconds.
|
|
#autosave_on_changes false
|
|
|
|
# Save persistent message data to disk (true/false).
|
|
# This saves information about all messages, including
|
|
# subscriptions, currently in-flight messages and retained
|
|
# messages.
|
|
# retained_persistence is a synonym for this option.
|
|
#persistence false
|
|
|
|
# The filename to use for the persistent database, not including
|
|
# the path.
|
|
#persistence_file mosquitto.db
|
|
|
|
# Location for persistent database. Must include trailing /
|
|
# Default is an empty string (current directory).
|
|
# Set to e.g. /var/lib/mosquitto/ if running as a proper service on Linux or
|
|
# similar.
|
|
#persistence_location
|
|
|
|
|
|
# =================================================================
|
|
# Logging
|
|
# =================================================================
|
|
|
|
# Places to log to. Use multiple log_dest lines for multiple
|
|
# logging destinations.
|
|
# Possible destinations are: stdout stderr syslog topic file
|
|
#
|
|
# stdout and stderr log to the console on the named output.
|
|
#
|
|
# syslog uses the userspace syslog facility which usually ends up
|
|
# in /var/log/messages or similar.
|
|
#
|
|
# topic logs to the broker topic '$SYS/broker/log/<severity>',
|
|
# where severity is one of D, E, W, N, I, M which are debug, error,
|
|
# warning, notice, information and message. Message type severity is used by
|
|
# the subscribe/unsubscribe log_types and publishes log messages to
|
|
# $SYS/broker/log/M/susbcribe or $SYS/broker/log/M/unsubscribe.
|
|
#
|
|
# The file destination requires an additional parameter which is the file to be
|
|
# logged to, e.g. "log_dest file /var/log/mosquitto.log". The file will be
|
|
# closed and reopened when the broker receives a HUP signal. Only a single file
|
|
# destination may be configured.
|
|
#
|
|
# Note that if the broker is running as a Windows service it will default to
|
|
# "log_dest none" and neither stdout nor stderr logging is available.
|
|
# Use "log_dest none" if you wish to disable logging.
|
|
#log_dest stderr
|
|
|
|
# Types of messages to log. Use multiple log_type lines for logging
|
|
# multiple types of messages.
|
|
# Possible types are: debug, error, warning, notice, information,
|
|
# none, subscribe, unsubscribe, websockets, all.
|
|
# Note that debug type messages are for decoding the incoming/outgoing
|
|
# network packets. They are not logged in "topics".
|
|
#log_type error
|
|
#log_type warning
|
|
#log_type notice
|
|
#log_type information
|
|
|
|
|
|
# If set to true, client connection and disconnection messages will be included
|
|
# in the log.
|
|
#connection_messages true
|
|
|
|
# If using syslog logging (not on Windows), messages will be logged to the
|
|
# "daemon" facility by default. Use the log_facility option to choose which of
|
|
# local0 to local7 to log to instead. The option value should be an integer
|
|
# value, e.g. "log_facility 5" to use local5.
|
|
#log_facility
|
|
|
|
# If set to true, add a timestamp value to each log message.
|
|
#log_timestamp true
|
|
|
|
# Set the format of the log timestamp. If left unset, this is the number of
|
|
# seconds since the Unix epoch.
|
|
# This is a free text string which will be passed to the strftime function. To
|
|
# get an ISO 8601 datetime, for example:
|
|
# log_timestamp_format %Y-%m-%dT%H:%M:%S
|
|
#log_timestamp_format
|
|
|
|
# Change the websockets logging level. This is a global option, it is not
|
|
# possible to set per listener. This is an integer that is interpreted by
|
|
# libwebsockets as a bit mask for its lws_log_levels enum. See the
|
|
# libwebsockets documentation for more details. "log_type websockets" must also
|
|
# be enabled.
|
|
#websockets_log_level 0
|
|
|
|
|
|
# =================================================================
|
|
# Security
|
|
# =================================================================
|
|
|
|
# If set, only clients that have a matching prefix on their
|
|
# clientid will be allowed to connect to the broker. By default,
|
|
# all clients may connect.
|
|
# For example, setting "secure-" here would mean a client "secure-
|
|
# client" could connect but another with clientid "mqtt" couldn't.
|
|
#clientid_prefixes
|
|
|
|
# Boolean value that determines whether clients that connect
|
|
# without providing a username are allowed to connect. If set to
|
|
# false then a password file should be created (see the
|
|
# password_file option) to control authenticated client access.
|
|
#
|
|
# Defaults to true if no other security options are set. If `password_file` or
|
|
# `psk_file` is set, or if an authentication plugin is loaded which implements
|
|
# username/password or TLS-PSK checks, then `allow_anonymous` defaults to
|
|
# false.
|
|
#
|
|
allow_anonymous false
|
|
|
|
# -----------------------------------------------------------------
|
|
# Default authentication and topic access control
|
|
# -----------------------------------------------------------------
|
|
|
|
# Control access to the broker using a password file. This file can be
|
|
# generated using the mosquitto_passwd utility. If TLS support is not compiled
|
|
# into mosquitto (it is recommended that TLS support should be included) then
|
|
# plain text passwords are used, in which case the file should be a text file
|
|
# with lines in the format:
|
|
# username:password
|
|
# The password (and colon) may be omitted if desired, although this
|
|
# offers very little in the way of security.
|
|
#
|
|
# See the TLS client require_certificate and use_identity_as_username options
|
|
# for alternative authentication options. If an auth_plugin is used as well as
|
|
# password_file, the auth_plugin check will be made first.
|
|
#password_file
|
|
|
|
# Access may also be controlled using a pre-shared-key file. This requires
|
|
# TLS-PSK support and a listener configured to use it. The file should be text
|
|
# lines in the format:
|
|
# identity:key
|
|
# The key should be in hexadecimal format without a leading "0x".
|
|
# If an auth_plugin is used as well, the auth_plugin check will be made first.
|
|
#psk_file
|
|
|
|
# Control access to topics on the broker using an access control list
|
|
# file. If this parameter is defined then only the topics listed will
|
|
# have access.
|
|
# If the first character of a line of the ACL file is a # it is treated as a
|
|
# comment.
|
|
# Topic access is added with lines of the format:
|
|
#
|
|
# topic [read|write|readwrite] <topic>
|
|
#
|
|
# The access type is controlled using "read", "write" or "readwrite". This
|
|
# parameter is optional (unless <topic> contains a space character) - if not
|
|
# given then the access is read/write. <topic> can contain the + or #
|
|
# wildcards as in subscriptions.
|
|
#
|
|
# The first set of topics are applied to anonymous clients, assuming
|
|
# allow_anonymous is true. User specific topic ACLs are added after a
|
|
# user line as follows:
|
|
#
|
|
# user <username>
|
|
#
|
|
# The username referred to here is the same as in password_file. It is
|
|
# not the clientid.
|
|
#
|
|
#
|
|
# If is also possible to define ACLs based on pattern substitution within the
|
|
# topic. The patterns available for substition are:
|
|
#
|
|
# %c to match the client id of the client
|
|
# %u to match the username of the client
|
|
#
|
|
# The substitution pattern must be the only text for that level of hierarchy.
|
|
#
|
|
# The form is the same as for the topic keyword, but using pattern as the
|
|
# keyword.
|
|
# Pattern ACLs apply to all users even if the "user" keyword has previously
|
|
# been given.
|
|
#
|
|
# If using bridges with usernames and ACLs, connection messages can be allowed
|
|
# with the following pattern:
|
|
# pattern write $SYS/broker/connection/%c/state
|
|
#
|
|
# pattern [read|write|readwrite] <topic>
|
|
#
|
|
# Example:
|
|
#
|
|
# pattern write sensor/%u/data
|
|
#
|
|
# If an auth_plugin is used as well as acl_file, the auth_plugin check will be
|
|
# made first.
|
|
#acl_file
|
|
|
|
# -----------------------------------------------------------------
|
|
# External authentication and topic access plugin options
|
|
# -----------------------------------------------------------------
|
|
|
|
# External authentication and access control can be supported with the
|
|
# auth_plugin option. This is a path to a loadable plugin. See also the
|
|
# auth_opt_* options described below.
|
|
#
|
|
# The auth_plugin option can be specified multiple times to load multiple
|
|
# plugins. The plugins will be processed in the order that they are specified
|
|
# here. If the auth_plugin option is specified alongside either of
|
|
# password_file or acl_file then the plugin checks will be made first.
|
|
#
|
|
#auth_plugin
|
|
|
|
# If the auth_plugin option above is used, define options to pass to the
|
|
# plugin here as described by the plugin instructions. All options named
|
|
# using the format auth_opt_* will be passed to the plugin, for example:
|
|
#
|
|
# auth_opt_db_host
|
|
# auth_opt_db_port
|
|
# auth_opt_db_username
|
|
# auth_opt_db_password
|
|
|
|
|
|
# =================================================================
|
|
# Bridges
|
|
# =================================================================
|
|
|
|
# A bridge is a way of connecting multiple MQTT brokers together.
|
|
# Create a new bridge using the "connection" option as described below. Set
|
|
# options for the bridges using the remaining parameters. You must specify the
|
|
# address and at least one topic to subscribe to.
|
|
#
|
|
# Each connection must have a unique name.
|
|
#
|
|
# The address line may have multiple host address and ports specified. See
|
|
# below in the round_robin description for more details on bridge behaviour if
|
|
# multiple addresses are used. Note that if you use an IPv6 address, then you
|
|
# are required to specify a port.
|
|
#
|
|
# The direction that the topic will be shared can be chosen by
|
|
# specifying out, in or both, where the default value is out.
|
|
# The QoS level of the bridged communication can be specified with the next
|
|
# topic option. The default QoS level is 0, to change the QoS the topic
|
|
# direction must also be given.
|
|
#
|
|
# The local and remote prefix options allow a topic to be remapped when it is
|
|
# bridged to/from the remote broker. This provides the ability to place a topic
|
|
# tree in an appropriate location.
|
|
#
|
|
# For more details see the mosquitto.conf man page.
|
|
#
|
|
# Multiple topics can be specified per connection, but be careful
|
|
# not to create any loops.
|
|
#
|
|
# If you are using bridges with cleansession set to false (the default), then
|
|
# you may get unexpected behaviour from incoming topics if you change what
|
|
# topics you are subscribing to. This is because the remote broker keeps the
|
|
# subscription for the old topic. If you have this problem, connect your bridge
|
|
# with cleansession set to true, then reconnect with cleansession set to false
|
|
# as normal.
|
|
#connection <name>
|
|
#address <host>[:<port>] [<host>[:<port>]]
|
|
#topic <topic> [[[out | in | both] qos-level] local-prefix remote-prefix]
|
|
|
|
|
|
# If a bridge has topics that have "out" direction, the default behaviour is to
|
|
# send an unsubscribe request to the remote broker on that topic. This means
|
|
# that changing a topic direction from "in" to "out" will not keep receiving
|
|
# incoming messages. Sending these unsubscribe requests is not always
|
|
# desirable, setting bridge_attempt_unsubscribe to false will disable sending
|
|
# the unsubscribe request.
|
|
#bridge_attempt_unsubscribe true
|
|
|
|
# Set the version of the MQTT protocol to use with for this bridge. Can be one
|
|
# of mqttv311 or mqttv11. Defaults to mqttv311.
|
|
#bridge_protocol_version mqttv311
|
|
|
|
# Set the clean session variable for this bridge.
|
|
# When set to true, when the bridge disconnects for any reason, all
|
|
# messages and subscriptions will be cleaned up on the remote
|
|
# broker. Note that with cleansession set to true, there may be a
|
|
# significant amount of retained messages sent when the bridge
|
|
# reconnects after losing its connection.
|
|
# When set to false, the subscriptions and messages are kept on the
|
|
# remote broker, and delivered when the bridge reconnects.
|
|
#cleansession false
|
|
|
|
# Set the amount of time a bridge using the lazy start type must be idle before
|
|
# it will be stopped. Defaults to 60 seconds.
|
|
#idle_timeout 60
|
|
|
|
# Set the keepalive interval for this bridge connection, in
|
|
# seconds.
|
|
#keepalive_interval 60
|
|
|
|
# Set the clientid to use on the local broker. If not defined, this defaults to
|
|
# 'local.<clientid>'. If you are bridging a broker to itself, it is important
|
|
# that local_clientid and clientid do not match.
|
|
#local_clientid
|
|
|
|
# If set to true, publish notification messages to the local and remote brokers
|
|
# giving information about the state of the bridge connection. Retained
|
|
# messages are published to the topic $SYS/broker/connection/<clientid>/state
|
|
# unless the notification_topic option is used.
|
|
# If the message is 1 then the connection is active, or 0 if the connection has
|
|
# failed.
|
|
# This uses the last will and testament feature.
|
|
#notifications true
|
|
|
|
# Choose the topic on which notification messages for this bridge are
|
|
# published. If not set, messages are published on the topic
|
|
# $SYS/broker/connection/<clientid>/state
|
|
#notification_topic
|
|
|
|
# Set the client id to use on the remote end of this bridge connection. If not
|
|
# defined, this defaults to 'name.hostname' where name is the connection name
|
|
# and hostname is the hostname of this computer.
|
|
# This replaces the old "clientid" option to avoid confusion. "clientid"
|
|
# remains valid for the time being.
|
|
#remote_clientid
|
|
|
|
# Set the password to use when connecting to a broker that requires
|
|
# authentication. This option is only used if remote_username is also set.
|
|
# This replaces the old "password" option to avoid confusion. "password"
|
|
# remains valid for the time being.
|
|
#remote_password
|
|
|
|
# Set the username to use when connecting to a broker that requires
|
|
# authentication.
|
|
# This replaces the old "username" option to avoid confusion. "username"
|
|
# remains valid for the time being.
|
|
#remote_username
|
|
|
|
# Set the amount of time a bridge using the automatic start type will wait
|
|
# until attempting to reconnect.
|
|
# This option can be configured to use a constant delay time in seconds, or to
|
|
# use a backoff mechanism based on "Decorrelated Jitter", which adds a degree
|
|
# of randomness to when the restart occurs.
|
|
#
|
|
# Set a constant timeout of 20 seconds:
|
|
# restart_timeout 20
|
|
#
|
|
# Set backoff with a base (start value) of 10 seconds and a cap (upper limit) of
|
|
# 60 seconds:
|
|
# restart_timeout 10 30
|
|
#
|
|
# Defaults to jitter with a base of 5 and cap of 30
|
|
#restart_timeout 5 30
|
|
|
|
# If the bridge has more than one address given in the address/addresses
|
|
# configuration, the round_robin option defines the behaviour of the bridge on
|
|
# a failure of the bridge connection. If round_robin is false, the default
|
|
# value, then the first address is treated as the main bridge connection. If
|
|
# the connection fails, the other secondary addresses will be attempted in
|
|
# turn. Whilst connected to a secondary bridge, the bridge will periodically
|
|
# attempt to reconnect to the main bridge until successful.
|
|
# If round_robin is true, then all addresses are treated as equals. If a
|
|
# connection fails, the next address will be tried and if successful will
|
|
# remain connected until it fails
|
|
#round_robin false
|
|
|
|
# Set the start type of the bridge. This controls how the bridge starts and
|
|
# can be one of three types: automatic, lazy and once. Note that RSMB provides
|
|
# a fourth start type "manual" which isn't currently supported by mosquitto.
|
|
#
|
|
# "automatic" is the default start type and means that the bridge connection
|
|
# will be started automatically when the broker starts and also restarted
|
|
# after a short delay (30 seconds) if the connection fails.
|
|
#
|
|
# Bridges using the "lazy" start type will be started automatically when the
|
|
# number of queued messages exceeds the number set with the "threshold"
|
|
# parameter. It will be stopped automatically after the time set by the
|
|
# "idle_timeout" parameter. Use this start type if you wish the connection to
|
|
# only be active when it is needed.
|
|
#
|
|
# A bridge using the "once" start type will be started automatically when the
|
|
# broker starts but will not be restarted if the connection fails.
|
|
#start_type automatic
|
|
|
|
# Set the number of messages that need to be queued for a bridge with lazy
|
|
# start type to be restarted. Defaults to 10 messages.
|
|
# Must be less than max_queued_messages.
|
|
#threshold 10
|
|
|
|
# If try_private is set to true, the bridge will attempt to indicate to the
|
|
# remote broker that it is a bridge not an ordinary client. If successful, this
|
|
# means that loop detection will be more effective and that retained messages
|
|
# will be propagated correctly. Not all brokers support this feature so it may
|
|
# be necessary to set try_private to false if your bridge does not connect
|
|
# properly.
|
|
#try_private true
|
|
|
|
# -----------------------------------------------------------------
|
|
# Certificate based SSL/TLS support
|
|
# -----------------------------------------------------------------
|
|
# Either bridge_cafile or bridge_capath must be defined to enable TLS support
|
|
# for this bridge.
|
|
# bridge_cafile defines the path to a file containing the
|
|
# Certificate Authority certificates that have signed the remote broker
|
|
# certificate.
|
|
# bridge_capath defines a directory that will be searched for files containing
|
|
# the CA certificates. For bridge_capath to work correctly, the certificate
|
|
# files must have ".crt" as the file ending and you must run "openssl rehash
|
|
# <path to capath>" each time you add/remove a certificate.
|
|
#bridge_cafile
|
|
#bridge_capath
|
|
|
|
|
|
# If the remote broker has more than one protocol available on its port, e.g.
|
|
# MQTT and WebSockets, then use bridge_alpn to configure which protocol is
|
|
# requested. Note that WebSockets support for bridges is not yet available.
|
|
#bridge_alpn
|
|
|
|
# When using certificate based encryption, bridge_insecure disables
|
|
# verification of the server hostname in the server certificate. This can be
|
|
# useful when testing initial server configurations, but makes it possible for
|
|
# a malicious third party to impersonate your server through DNS spoofing, for
|
|
# example. Use this option in testing only. If you need to resort to using this
|
|
# option in a production environment, your setup is at fault and there is no
|
|
# point using encryption.
|
|
#bridge_insecure false
|
|
|
|
# Path to the PEM encoded client certificate, if required by the remote broker.
|
|
#bridge_certfile
|
|
|
|
# Path to the PEM encoded client private key, if required by the remote broker.
|
|
#bridge_keyfile
|
|
|
|
# -----------------------------------------------------------------
|
|
# PSK based SSL/TLS support
|
|
# -----------------------------------------------------------------
|
|
# Pre-shared-key encryption provides an alternative to certificate based
|
|
# encryption. A bridge can be configured to use PSK with the bridge_identity
|
|
# and bridge_psk options. These are the client PSK identity, and pre-shared-key
|
|
# in hexadecimal format with no "0x". Only one of certificate and PSK based
|
|
# encryption can be used on one
|
|
# bridge at once.
|
|
#bridge_identity
|
|
#bridge_psk
|
|
|
|
|
|
# =================================================================
|
|
# External config files
|
|
# =================================================================
|
|
|
|
# External configuration files may be included by using the
|
|
# include_dir option. This defines a directory that will be searched
|
|
# for config files. All files that end in '.conf' will be loaded as
|
|
# a configuration file. It is best to have this as the last option
|
|
# in the main file. This option will only be processed from the main
|
|
# configuration file. The directory specified must not contain the
|
|
# main configuration file.
|
|
# Files within include_dir will be loaded sorted in case-sensitive
|
|
# alphabetical order, with capital letters ordered first. If this option is
|
|
# given multiple times, all of the files from the first instance will be
|
|
# processed before the next instance. See the man page for examples.
|
|
#include_dir
|